Boarding Up Windows And Doors Techniques To Simplify Your Daily Life Boarding Up Windows And Doors Trick Every Person Should Learn > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

boarding up windows and doors [Read Home ] Before a Storm Hits

Before a storm hits and your windows are smashed, boarding up property them up and doors can protect your home from damage. To do this, you'll need to have a few things in your desk.

First, measure the window's height and width, including the framing (not the trim around it or masonry). Note these measurements so you won't forget.

Preparation

It is always recommended to put up a board on doors and windows prior to a storm or other natural disaster strikes. This will help prevent damage to property and reduce the loss of life. Boarding up windows requires an extensive amount of preparation, like purchasing and measuring plywood boards and identifying the exact size of each window to be covered. It takes time to cut and put in the boards correctly. Fortunately this can be simplified by starting the preparations when you first hear of a possible storm coming in your area. You can avoid a stressful rush in the last minute, and make it easier for you and your staff.

Begin by listening to forecasters for weather and follow the guidelines laid out by your local government. The earlier you start the process the better, since it allows you plenty of time to gather and store the needed items without being pushed by a rapidly approaching storm. You may require a substantial amount of plywood to cover your windows, dependent on the severity and intensity of the storm. Make use of a tape to determine the width and height of each window opening. Make sure to include the framing or trim around each window, as well as any extended ledges if necessary.

Divide the width and the height of your window by 2 to determine the amount of plywood sheets that you'll require. service for boarding up windows instance, if the width of your window is 16 inches, the thickness of each sheet should be 8 inches. If you have an exterior made of wood, you should drill pilot holes in the plywood sheet that align with the window frame beneath to avoid splitting when screwing in the screws.

If you have a bigger window opening than one sheet of plywood can handle cut two sheets of plywood that are each half as large as the desired window. Then, place them side by side on the wall. Cut a piece 2 by 4 inches (5.1 10.2 cm) 10.2 cm) of lumber to the length of the connecting edge between the plywood sheets, and place it on top of the seam. Then then, drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them.

Materials

To ensure safety and security ensure safety and security, use only materials that are durable and will not break or shatter in high winds. The most commonly used material to board up windows is plywood, which is inexpensive accessible and simple to work with. Choose plywood that is exterior grade (CDX), as it will be stronger and contain fewer warps and knots. A stronger option is storm shutters or hurricane shutters, which are erected over windows already in use to offer more protection from glass breaking and the weather that can cause a lot of damage.

Once you've determined the location of the window openings take measurements of the height and width of each one to determine how much plywood you will need. Then you can use the power drill to drill pilot holes into the plywood sheets at two-inch intervals around each window. Before attaching the plywood, you must identify and mark the locations of studs on the wall to ensure that the boards are anchored securely. If you have wood siding on your home, look for nailheads in order to determine stud location. You could also use your drill to determine the studs' locations. Be sure to insert the screws into the framing and not the sheathing or trim; a plywood panel attached only to these materials could become a hazard in strong winds.

If your window is too large for one sheet of plywood, you could cut two pieces of plywood each half the size and join them using two by four inches of lumber. Label each plywood panel so that you know which window it will be covering.

To attach the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to get through both the sheathing and the studs. To attach the plywood panels to the wall, use screws made of corrosion-resistant that are long enough to penetrate the sheathing as well as the studs.

In addition to protecting your windows, you should also place an "No Trespassing" sign on your property, and consider installing polycarbonate security glass such as DefenseLite over your primary windows. These transparent shields are fixed over existing glazing and protect your windows and door. They are virtually indestructible and can deter burglars from gaining entry into your home.

Installation

If you live in or are planning to move to a region which is susceptible to hurricanes and are worried about the possibility of a storm it is recommended to board up all your windows and doors. This task can be completed quickly and efficiently, but only if the boards are measured, cut, and labeled before the storm hits.

You'll require additional tools which include a drill, a saw (or a hammer with nails in the event that you don't have a power tool) and an erecting level, gloves and safety glasses. It is a good idea to coat the plywood with sealant and make it waterproof.

Begin by measuring each window's height and width. Then, cut your plywood sheets to fit within the frames. This is best done on the spot as you are more in control of the exact dimensions.

Cut the boards to the size you want with a track or circular saw. Once they're installed you'll need to sand them down completely. them. Once the boards are set put the 3 inch stainless steel hanger screws into the framing posts around each window. Use washers to secure each bolt as well as wings nuts. Make sure that each screw penetrates at least 2 inches into the studs to ensure that the boarding up doorway is strong enough to withstand high winds.

If you're building using concrete blocks, you can join the plywood with pan head screws that are galvanized and which are driven into the edges of the panels to masonry or cinder block. It is also necessary to drill pilot holes in the masonry before screwing corrosion-resistant screws into the holes. The project could take about three hours per time period. It is crucial to begin as soon as an alert for hurricanes has been issued. This will allow you enough time to complete your project before the storm hits.

Maintenance

If you're a homeowner, or business owner, it is essential to have the right materials to board up doors and windows ahead of a severe storm. This will help you to avoid costly repairs and protect your home from further damage that could be caused by wind, rain, flying objects and other causes.

The right tools will make the boarding up a doorway up process much easier and quicker to complete. The most important thing is to accurately determine the dimensions of the windows you have to cover. This will ensure the OSB or plywood is fitted snugly and won't come off easily. If you're using plywood, ensure that you are using exterior-grade sheets and think about adding an extra layer of protection.

After you have the plywood or OSB measured, mark the areas where screws will go into the board. Use a drill to predrill holes at 12-inch intervals in the plywood. This will allow you to securely fasten the boards with hanger bolts during an emergency or in the event of a disaster. After the storm has gone away and you've received all-clear from local authorities, take off the hanger bolts, but keep them in place for any future emergency boarding up 24/7 situations.

The next step is to install the plywood panels on top of the windows. This is a job for two people So, be prepared prior to starting. If you are using plywood, sand the edges to make them smooth so that they don't scratch paint or damage trim. Then use corrosion-resistant screws to attach the plywood using the pilot holes. If your home has shingles made of vinyl on it, attach the plywood directly to the shingles, and not to the wood framing.

A window that has been boarded up may be used to stop burglars. Burglars are more likely to take aim at a structure with a broken or unlocked window. They are also more likely to break into the store with a boarded up window than one that has no. If you're a retailer owner, this is something you need to consider seriously.