14 Businesses Are Doing A Fantastic Job At Door Lock Change > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock replacement is a quick and cheap method to increase your home's security. However, the procedure isn't for all. It requires some expertise and perseverance.

The cylinder is located within the knob body. The cylinder recognizes the key when it is placed into the lock.

Removing the old lock

The first step in replacing a door lock is to remove the lock that was previously in use. It's a fairly simple procedure, but there are some things to remember. First, ensure that your new lock is the correct size for your door. This will ensure that it fits securely, and doesn't leave a gap in the latch or deadbolt.

After you have removed the latch plate, you'll need to look for two bolts or screws in the casing's interior that are holding the casing together with the lock halves. Remove them with a screwdriver, then take the lock out of the door. If you have a mortise lock, there may be a set screw located at the base of the handle that binds it to the spindle. Use a screwdriver to unscrew this screw, then pull out the doorknobs.

You must also take the deadbolt and latch plug from the hole in your door jamb. Install the new lock. If you are replacing a mortise you must measure the distance between your lock's case and your door's edge to ensure that the new lock is a good fit.

You might want to change your lock for a variety reasons, such as when you suspect that someone else has the key, or if you've got an incoming roommate. In any event, you could save money by taking the lock off yourself, rather than hiring a professional to do it. It's much simpler than most people imagine and can be completed in a matter of minutes.

Start by removing the handle and trim from your door. Then, pull the trim off using a screwdriver that is flat. It should be possible to pull off the majority of it. In certain cases you might be able to take off the handles completely. The next step is to look for a pinhole on the inside of the handle, and insert a straightened clip into it. This will activate the release mechanism and allow you to take the handle from the door. Then, look on the interior side of the lock for a small tab, and then press it with a flat screwdriver. After the spindle is removed, you are able to remove the cylinder and the housing.

Selecting a new lock

You have many options when it comes to choosing a new lock. Take a look at the various types of locks and select one that fits the style of your door. Consider the backset (the distance between the edge of the door and the center of the hole in the lock) and the cross bore (small hole along the edge of the door frame). Also, make sure to choose a upvc window lock replacement that will accommodate the door's thickness as well as swing.

The American National Standards Institute and BHMA have graded the majority of door locks to give an idea of their durability and the difficulty to pick them or disable them. A grade 3 lock could be a good choice for a tranquil urban apartment complex, whereas an entry grade lock could be more able to withstand the traffic at a busy store front on a city street.

Most smart door locks need a digital code to open. If you are concerned about hacking or other security issues, talk to an expert locksmith.

Replacing the cylinder

If your door lock's cylinder is damaged or broken you can repair it in a matter of minutes by completing a do-it-yourself project. The trick is to select the correct cylinder and follow the instructions that come with it. First, you must remove the handle or knob if it is present. Then using a screwdriver take off the trim around the lock cylinder. Once the trim has been removed, it is possible to remove the screws that hold the cylinder in place using the flathead. The cylinder is then gently removed from the door.

Before you install the new cylinder, make sure that it is the correct length for your door. Measure the distance from the center to the left and right sides of the cylinder using the aid of a tape measure. Purchase a new cylinder which has the same measurements. This will stop the cylinder from snapping, which can happen when the door is kicked out or when the key gets stuck inside.

Install the replacement cylinder into the door, and then turn the key. This will align the cylinder with the carriage that is usually located on the outside of your upvc window lock mechanism replacement. Then, loosen the set screw, which should be just a couple of turns in the head. If there is a screw at the edge of the case that holds the door, you'll have to loosen it.

You can replace the lock cylinder you have used with the new one by slipping it into the case, and tightening the set screws. Reinstalling the piece that connects a cylinder with an indicator stem for a lock is also crucial. This can be done by pulling three small tabs on the back of the cylindrical using needle-nosed pliers. Then, you can attach the second bracket to the back of the cylinder. Then, you must put back in the strike plate and latch plate as well as the retaining ring that is attached to the top of the lock cylinder.

Installing a new lock

If you're replacing an old double glazing window lock repairs near me lock repair [have a peek here], you must begin by measuring the width of your door. Most residential locksets are designed for a door thickness of 1 3/8 to 3/4 inch. If your door is thicker it will require a thick door kit that includes longer screws, a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

Most locks come with detailed instruction manual to assist you in installing the new hardware. Before beginning, you must read the instructions to ensure you've followed all the steps. The guide will give you an idea of how much skill is required to complete the task. It is possible to ask a friend who has worked with locks for assistance if are changing a lock the first time.

Before installing the new lock, it's recommended to tape over the openings of the old hardware. This will stop the screws from slipping out of the holes, and will protect any tile you might have put in the area. This will also protect your tiles from damage caused by dirt, rust and grime. SECURAM Touch includes an ad-hoc strip of masking tape or gaffer tape. However, you can use any tape you own.

Once you've removed the screws that connect the interior half of the lock section to the outside side immediately, pull it back. This should be done swiftly to prevent the lock from accidentally closing and harming the mechanism.

Install the new latch bolt in the upper cross bore of your new lock if it has one. Make sure that you place it in the proper position, which is marked by an arrow. Then, place the latch plate on top of the bolt and secure it in place.

Screw the deadbolt into the jamb on the door. Test the deadbolt a few times by throwing it to ensure it is extending into the strike plate. If you're using an electronic smart lock, be certain to follow the instructions for programming it. This involves downloading an application and registering your email address, confirming your identity, and connecting to the wireless network to add your device.